Expert Answers about Toyota Truck Ramps

• What is the Weight Capacity of the Race Ramps Racing Scale Ramps Part # RR-SCALE
• The Race Ramps Racing Scale Ramps part # RR-SCALE have a 1,500 lb per ramp capacity. This would be suitable for just the front axle of most pickup trucks. The ramp will provide you with a 2.5" lift and should be just what you need to edge the truck over the concrete curb in your garage. Another similar option we have they you may want to look at is the Race Ramps Trak-Jax Ramps part # RR-TJ which also have a 1,500 lb per ramp capacity but will provide you with a 3" lift.
  view full answer...


• Fit & Compatibility of Erickson Ramps on a Chevrolet Silverado 2500HD with Bed Height of 39 Inches
• There is not a height restriction for the Erickson Ramps # EM07464-2. These could work for your truck and golf cart, after doing some calculations, I found that the angle the golf cart would need to climb with the 80 inch Erickson Ramps # EM07464-2, you were looking at, installed on your Chevrolet Silverado 2500HD will be 29.17 degrees. For a less steep 25 degree incline from ground to truck bed, I recommend the 90 inch long Erickson Ramps # EM07486. I have linked both products to this...
  view full answer...


• Would the Curt Cargo Carrier FHG69ZR fit a 2006 Ford E-450 Truck
• As long as you have a trailer hitch with a 2 inch opening at the rear of your Ford E-450 the Flint Hill Goods cargo carrier with ramp part # FHG69VR is going to attach to the vehicle. Most ramped carriers have a 48-inch ramp, which is a concern about the height of the truck causing the slope of the 48" ramp to be too steep. This carrier has a 60-inch ramp which would be much better. You could measure 60 inches sidways from the hitch opening to the ground to check out the slope of this...
  view full answer...


• ATV Ramps Needed For Loading A Kawasaki Mule Into A U-Pack Semi Trailer
• U-Pack Semi Trailers have a 48" height from the ground whereas the typical application for ATV ramps like the CargoSmart Arched Loading Ramp Set # 3483070 are trailers and truck beds which are usually at most 23" inches in height. Because of this the ramps will be very steep when used on a U-Pack trailer but should allow you to get your Kawasaki Mule loaded. These ramps are rated for 3,000lbs which is almost double the curb weight of your Kawasaki Mule. They have cam-buckle straps to prevent...
  view full answer...


• Longest Set of Folding Ramps for Loading Generator in Truck Bed
• The longest folding ramps we have for you is the Arched Loading Ramp Set part # 288-07432 for 1 or part # 288-07432-2 for 2 which are 90" long. The 90" length will ensure the angle that will be required to load the generator in your truck bed is not too steep. They are reasonably priced and very lightweight weighing in at only 23.5 lbs per ramp. The great thing about these ramps is that they have cam buckle safety straps that prevent the ramp from sliding out during loading and unloading.
  view full answer...


• What Ramps Are Good For Loading A Car Onto A Flat Bed Truck
• I do not think the Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2 # 288-07503 would be the safest set of ramps for this particular job. They can handle the weight of the car no problem but looking at the picture you provided I do no think the angle of the ramps will be low enough to let the car get on the flat bed without bottoming out. I definetly recommend going with a longer set of ramps like the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000...
  view full answer...


• Do the Mad-Ramps Pivoting Ramp System Fit Specific Trucks
• The great thing about the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps # MR54FR is that they are a universal application so as long as your trucks can handle the weight of your 2011 Honda Rubicon 500 and the Honda has a wheelbase no larger than 88" and it isn't over 60" wide you'll be good to go! Attached is a review video for you to check out.
  view full answer...


• What is Ramp Angle of Flint Hill Goods 30x50 Wheelchair Carrier w/ 48 Long Ramp in Full Size Truck
• We had the chance to install the Flint Hill Goods 30x50 Wheelchair Carrier w/ 48" Long Ramp # FHG77ZR on a similar size truck as your F-150 and we found that the 48-inch-long ramp made the incline very steep. I would encourage you to instead take a look at the 29x49 Aluminum Flint Hill Goods Wheelchair carrier # FHG69ZR. The # FHG69ZR has a 60 inch ramp that should work for you. I attached a picture that shows an older, discontinued, carrier with a 60" ramp installed on a similar sized...
  view full answer...


• Would Stallion Arched Ramps Loading Ramp Set Be Good For Loading Snowblower Into Truck Bed
• The # 288-07432-2 loading ramp would be an excellent choice for loading a self-propelled snowblower into the bed of your Silverado. The rungs on the ramps will provide excellent traction for both the tires on the snowblower, and for the person loading it. If you click the provided link, you can see a demonstration video featuring the ramps.
  view full answer...


• Can Erickson Arched Loading Ramp Be Used For Loading Dirt Bike And Street Bike
• The Erickson Arched Loading Ramp, part # EM07464 would work well for you to load your bikes in the back of a truck or trailer. This ramp weighs 30 lbs and is hinged in the center for easy storage and even has handles to make carrying it easier. This has a mesh surface that makes cleaning a breeze. The ramp is 80 inches long and 11 inches wide and has a weight capacity of 800 lbs.
  view full answer...


• Trailer Hitch Receiver Compatible With Mad-Ramps For a 2022 Toyota Tundra
• Yes, we have the Curt Trailer Hitch Receiver # C44BR which is custom fit for you 2022 Toyota Tundra that did not come with a receiver. This will allow you to be able to use the Mad-Ramps Pivoting Ramp System # MR54FR for carrying your ATV or UTV.
  view full answer...


• Can Mad-Ramps Pivoting Ramp System be Used to Load Zero Turn Mower
• The space between the rungs on the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps # MR54FR is 5-3/4". I'm not sure how that will fit with the smaller front tires of your ZTR. I'm sure the back ones will be just fine but the biggest issue I see is the deck on your mower coming into contact with the tailgate since the ramps start to pivot as the cargo weight shifts. Because of this I recommend going with a standard ramp set like the CargoSmart S-Curve Loading Ramp Set # 3483086-2 so you...
  view full answer...


• Will the Flint Hill Goods Cargo Carrier with ramp Part # FHG69ZR Work on a 1987 Ford F-150
• As long as your 1987 Ford F-150 has a 2" trailer hitch receiver like the Curt Trailer hitch Receiver part # 13028 then yes, the Flint Hill Goods Wheelchair Carrier part # FHG69ZR will fit on your truck. The only concern that I have is the height of your truck. You will need to decide if a 60" ramp will make the ramp too steep for your application. Take a look at pictures on this product page of this product on other trucks and see if you think that will be okay for you. You will...
  view full answer...


• Can the Conventional Ramp Door Spring be Used for a Box Truck Door
• Assuming all of the dimensions and capacity match up with what you have, you should be able to use the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer - Single Spring - 150-lb Capacity # 362SA8 for a roll up door. It is recommended to take this to an installer like a local garage door company unless you have experience with a torsion spring system. What I would do is send the information for the spring along with what you have on your box truck to the installer so they can...
  view full answer...


• Ramp Door Spring Assembly For a 8' Ramp Door on Cargo trailer Weighing 90lbs
• The Ramp Door Spring # M354FR is our closest setup for your cargo trailer door. This system is rated for a 120lb door so you will be able to add a Transition Plate # e32JR as well to your door which will make loading cargo using a dolly or hand truck much easier.
  view full answer...


• Could the Erickson Ramp EM07464-2 Be Used on a Van for Loading Pressure Washer
• As long as there is a decent ledge at the rear of your 2003 Chevy Express Van when the rear door is open the ramps part # EM07464-2 that you referenced would not slide or move while pushing up your pressure washer that is on wheels. I attached a picture that shows the brackets of the ramps that will rest on the rear cargo area of your van for you to check out. You will want to open the rear door of your van to see if the ramps would fit. Normally these ramps are used on truck tailgate...
  view full answer...


• Can 168" Long Gen-Y Hitch Aluminum Loading Ramp Set Be Used to Load Mower in Trailer
• The 168" Long Gen-Y Hitch Aluminum Loading Ramp Set # GH34FR should work out just fine at a height of about 45". I did some calculating and you're looking at about a 15 degree angle from where the bottom of the ramp will sit. The end of the ramp will also be about 162" out form where they connect to the trailer. You should be able to mock this up at home and see what kind of slope you're looking at with this solution.
  view full answer...


• Will Bed Extender Fit a 2012 Toyota Tacoma with a 6 Foot Bed
• The Curt # C57WR Universal Truck Bed Exender will fit nearly all full size pickup trucks including Chevrolet, GMC, Ford, Dodge, Ram, and Nissan, with 60" wide tail gates. (6.5 foot and longer beds) and provide 36-1/2 inches of additional bed length for storage and hauling. May not work with flare-style tailgates. Compatible with most tonneau covers You might also be interested in some ramps, like # CE26151PG, to help get the bike in the truck. This ramp is 60 inches long and 8-1/2 inches wide.
  view full answer...


• Using a Ramped Hitch Cargo Carrier on 5th Wheel Trailer and Pickup
• Ramped carriers like the Flint Hill Goods 30" x 50" Wheelchair Carrier w/ 48" Ramp - 2" Hitch # FHG77ZR will always have their ramps on the passenger side for safety reasons and even if it were possible to move it to the other side of the carrier this is not recommended. Although it is not what you might prefer it is a safer idea to check with Keystone about moving the ladder to the other side of the trailer. If you contact them with your VIN they can probably offer you some guidance about...
  view full answer...


• Will the Thule EasyFold XT Work with a Front-Mounted Hitch on My 2014 Toyota Tundra?
• You are correct in saying that the Thule EasyFold XT # TH903202 will work on a front hitch as long as you have enough bumper clearance. As far as the front bumper clearance when using your particular receiver, we unfortunately do not have an installation video with any of our hitches to provide a ballpark measurement on a 2014 Toyota Tundra. The distance of the center of the hitch's pinhole to the outside face of the bumper can vary widely between years/makes/models of vehicles. With that...
  view full answer...